Scroll back to top

    Circuits

    Circuits Overview

    Circuits traditionally consist of wires, power/current sources, resistors, capacitors, and inductors, and can be used for a vast variety of purposes. Due to the ways that these components affect voltage and current in a circuit, circuits are a useful way for us to physically interact with signals without needing digital filtering or circuit analysis. We have certain building blocks, and can construct circuits based on the parameters we need, which are current, voltage, and resistance. We can use this to solve most problems and construct physical filters. These allow us to avoid digital components and filters as they are often used to replicate the effect of physical components computationally. Using simple circuit components can reduce the footprint and the size scale of the device for portability and reduces energy consumption.

    Example: Passive RC Low Pass Filter
    Vin Resistor, R I Capacitor, C Vout
    Figure: Passive first-order RC low-pass filter topology.

    Interactive Circuit & Current Lab

    Use the interactive circuit simulator and calculator below to investigate how altering physical component values (\( R \) and \( C \)) changes total circuit impedance (\( |Z| \)), alters instantaneous current draw \( i(t) \), and shapes the output voltage \( V_{out} \). Switch between Low-Pass, High-Pass, and Resistive Divider modes in real time:

    Interactive Circuit, Current & Filter Lab

    Explore how physical circuit components dictate current flow, impedance, and signal filtering
    RC Low-Pass Filter Passband
    Circuit Schematic Electrons i(t)
    Oscilloscope
    Vin Vout i(t)
    1. AC Signal Generator
    5.0 V
    1.0 V 12.0 V
    1.00 kHz
    10 Hz 100 kHz
    2. Circuit Component Values
    1.00 kΩ
    100 Ω 100 kΩ
    100.00 nF
    1 nF 10 µF
    Circuit & Filter Calculator
    Total Current: 2.21 mA RMS (3.13 mA pk)
    Cutoff (fc)
    1.59 kHz
    Output (Vout)
    4.24 V
    Gain (|H|)
    -1.4 dB
    84.7% pass
    Reactance (XC)
    1.59 kΩ
    Impedance (|Z|)
    1.88 kΩ
    Phase (φ)
    -32.1°
    Cutoff: fc = 1 / (2πRC) = 1.59 kHz
    Ohm's Law: IRMS = Vin / |Z| = 2.21 mA • Ipk = 3.13 mA
    Adjust component values to observe how resistance and capacitance dictate circuit impedance and current flow.

    What are circuits?

    Circuits traditionally consist of wires, power/current sources, resistors, capacitors, and inductors, and can be used for a vast variety of purposes. In bioengineering, circuits provide the hardware foundation for acquiring biopotentials (such as ECG, EMG, and EEG) and physically filtering out electrical noise before digital conversion.

    Cross-Course Connection: Dr. Jenny Amos on Circuits & Conservation Laws

    Circuit analysis in biomedical engineering relies fundamentally on the conservation of charge and energy. To review the core circuit elements, voltage-current relationships, and Kirchhoff’s Laws taught by Dr. Jenny Amos in BIOE 202, explore these companion reference pages:

    Taught by Dr. Jenny Amos in BIOE 202 (Conservation Principles). Explore her course curriculum on the Conservation Principles Portal or visit Dr. Amos's Faculty Profile.

    Below is a table of basic elements in a circuit and their purpose:

    Element Name Symbol Purpose
    Resistor
    Resistor
    Switch
    Limits or controls the flow of current by converting some electrical energy into heat.
    Inductor
    Inductor Coil
    Stores energy in a magnetic field and resists sudden changes in current.
    Capacitor
    Non-polarized
    Polarized
    Stores energy in an electric field and resists sudden changes in voltage.
    Voltage Source
    AC Source
    + -
    DC Battery
    + -
    DC Independent
    Provides a fixed voltage across its terminals, pushing current through the circuit.
    Current Source
    Independent
    Controlled (Dependent)
    Provides a fixed current to the circuit, no matter what voltage that requires.
    Ground
    Chassis Ground
    Earth Ground
    Signal Ground
    Acts as the common reference point (0 V) from which all other voltages in the circuit are measured.

    Using Circuits for Filtering

    Due to the ways that circuit components affect voltage and current, circuits are a useful way for us to physically interact with signals without needing digital filtering or circuit analysis. We can construct circuits based on the parameters we need, which are current, voltage, and resistance.

    We can use this to construct physical filters. These allow us to avoid digital components and filters as they are often used to replicate the effect of physical components computationally. Using simple circuit components can reduce the footprint and the size scale of the device for portability and reduces energy consumption.

    Filter Circuit
    Low Pass Filter: an RC filter circuit made out of a resistor (\( R \)) and a capacitor (\( C \)) connected together to reject all unwanted high frequency signals.
    Cutoff Frequency: \( f_c = \frac{1}{2\pi RC} \)
    Vin Resistor, R Capacitor, C Vout
    High Pass Filter: an RC filter circuit made out of a resistor (\( R \)) and a capacitor (\( C \)) connected together to modify, reshape or reject all unwanted low frequency signals to produce a first-order frequency response.
    Cutoff Frequency: \( f_c = \frac{1}{2\pi RC} \)
    Vin Capacitor, C Resistor, R Vout
    Band Pass Filter: used to filter out certain frequencies that lie within a specific band or range of frequencies while attenuating all those that lie outside the band.
    Combines a high-pass stage and low-pass stage to isolate a desired bioelectric frequency band (e.g., ECG 0.5–100 Hz).
    Vin R1 C1 C2 R2 Vout